Product Search
Search results for 'D2171'
Showing 21 - 41 of 563 Total Results
(2) options
Location: Flow Cones
The grout flow cone from Test Mark is used to determine the flow of grout mixtures by measuring the time of efflux of a specified volume of grout from a flow cone.
CA-1574 #10
Location: Aggregate
Stainless steel wire cloth square for field rocker. Product CA-1574 #10; Test Mark Industries.
SA-1500
Location: Static Cone Penetrometer
Static Cone Penetrometers from Test Mark are used to evaluate the consistency of soils, their level of compaction and the bearing capacity of shallow foundations and pavement sub-grades.
Dynamic Cone Penetrometer only
SA-1225
Location: Dynamic Cone Penetrometer
The Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20" and can be used effectively in augured holes to depths of 15 to 20 feet. The DCP features a heat treated cone and zinc plated components.
(2) options
Location: Compaction Permeameter
The Compaction Permeameter from Test Mark is used for determining permeability of clay, sand and gravel soils using the Proctor plasticity compaction method.
SA-0360
Location: Soils
Glass plate with ground finish on one side and seamed edges. Dimensions: 12" x 12" x 3/8" thick.
CA-1320
Location: Hot Plates
Test Mark's laboratory hot plate features a white ceramic surface that is acid and alkali resistant. Non-heating frame surrounds the heated plate for added protection. Easy to set analog temperature control knob with graduated scale and LED display.
44 Gallon Water Tank - 24" x 18" x 24" deep (610 x 457 x 610 mm). Max. Oper. Temp. - 140°F (60°C)
CA-2744
Location: Parts & Accessories
Seamless, translucent tanks are ¼" (6.4 mm) thick with a drain faucet and overflow outlet. 44 gallon tank is 24" x 18" x 24" deep (610 x 457 x 610 mm). Maximum operating temperature is 140°F (60° C).
(5) options
Location: Manual Compression Testing Machines
Testing range of 300 to 30,000 lbs. (1.3 to 133.5 kN) with an accuracy of ±.5% of indicated load., Compact design requires minimal floor space. . Request a Quote The CM-30 was developed for testing concrete beams where accuracy and maintaining their required load pacing rate is an essential part of...
CA-1302
Location: Hot Plates
Durable die-cast single burner hot plate features high, medium, low and warm temperature settings. Power-on indicator light. Easy to use and clean.
SA-0200
Location: Sand Density
The Sand Cone Density Apparatus from Test Mark Industries determines the in-place density of soils.
SA-0350-S
Location: Plastic Limit
Plastic Limit Test Set consists of glass plate, 250 ml evaporating dish, spatula, 48 - 2.5 oz. sample tins and a 100 ml graduated glass cylinder.
iD-Indicator
Location: Digital Load Indicating Systems
Dual operating language option – display all test setup menu programs in either English or Spanish., Automatically calculates and displays peak stress at the end of a test. . Digital display in English Digital display in Spanish The iD indicator is the system of choice for testing programs where...
Dynamic Cone Penetrometer with Auger
SA-1200
Location: Dynamic Cone Penetrometer
Test Mark's Dynamic Cone Penetrometer (DCP) uses a 15 lb. steel mass that falls 20 inches and can be used effectively in augered holes to depths of 15 to 20 feet.
Digital Static Cone Penetrometer
SA-1510
Location: Static Cone Penetrometer
Digital Static Cone Penetrometer from Test Mark features a large digital readout making testing and recording readings easy.
CA-2170
Location: 30 Minute Timer
Plug aggregate equipment into the outlet at the back of the timer. Then plug timer cord into a wall outlet and turn the knob to the desired time. Time switch will turn off equipment automatically when time expires.